An RFQ may use “die casting,” “die cast,” “diecast,” or “pressure casting” for the same part. Spelling alone does not create a different manufacturing process; the more important ambiguity is failure to define the process type, material, and delivery condition.

In this article, die casting primarily means high-pressure die casting, or HPDC. The general word “pressure” needs qualification because low-pressure processes also exist in the foundry industry. Novin's production route is introduced on the Die-Casting Production page.

“Die Cast” and “Diecast” Are Common Forms of the Same English Term

“Die casting” is the standard English process term; “die cast” is commonly used as a noun or adjective, while the closed form “diecast” is also seen in general use. Use consistent wording in technical documents and define the intended process at first mention. Spelling does not determine part material, machine, or acceptance criteria.

State the part name and application, alloy, production volume, and delivery condition alongside the process name. This information lets a supplier assess the order against its production route. If the process is not yet fixed, identify it as a feasibility question.

What Exactly Does the Die-Casting Process Do?

NADCA defines high-pressure die casting as injecting molten metal into a reusable steel die. [1] After solidification and once the part is ready for ejection, the die opens and the casting is removed. Runners and excess material are separated in later operations.

A metal mold alone does not identify the process. Gravity permanent-mold casting also uses metal tooling, but its filling mechanism is not the same as HPDC. The Aluminum Association presents these methods separately. [2] In the order, state which features are formed in the die and which are completed after casting.

Cold Chamber and Hot Chamber: The Injection System Is Different

The terms hot chamber and cold chamber refer to the injection-system arrangement; “cold” does not mean that the metal is cold during injection. In a cold-chamber machine, molten metal is transferred to the shot sleeve for each cycle. NADCA identifies this route for aluminum and certain other alloys. [3]

In a hot-chamber machine, parts of the injection system are in contact with molten metal in the furnace. Alloy selection must consider temperature and compatibility with those components; NADCA lists zinc and other suitable alloys, including magnesium, among the applications. [4]

TopicHot ChamberCold Chamber
Injection arrangementSystem connected to furnace metalSeparate shot sleeve receiving molten metal
Metal supply for the shotNo separate ladling into the shot sleeve for each cycleMolten metal is transferred into the shot sleeve in a controlled manner
Example applicationZinc and alloys compatible with the systemAluminum and alloys compatible with the system

The table gives example applications, not an exclusive material list. For an RFQ, confirm the machine type together with the grade and part conditions.

High Pressure, Low Pressure, and Assisted Technologies

Low-pressure die casting (LPDC) is not the same as HPDC. In the industrial LPDC case studied by Ou and colleagues, gas pressure applied to metal in a holding furnace drove it through a transfer tube into the die cavity. [5] That mechanism differs from cold-chamber plunger injection. Because “die casting” also appears in the name LPDC, write the full process name in purchasing documents.

Vacuum assistance, squeeze casting, and semisolid processing are not interchangeable descriptions and must be reviewed against their actual specifications. The general term die casting does not establish weldability, heat-treatability, or a special level of internal quality.

High pressure alone does not guarantee elimination of entrapped gas. In an HPDC experiment, Iwata and colleagues examined residual entrapped gas and how its volume depended on pressure and solidification in the metal path. [6] Acceptance of internal quality or sealing performance requires product-specific requirements and tests.

Molten-metal transfer on the production lineImage source: Novin Industrial Group archive

Which Wording Is More Precise in a Search or RFQ?

When searching for a supplier, combine the part name with the intended material and process. For an RFQ, provide the drawing or model, application, grade or material need, production volume, critical characteristics, finishing operations, and quality criteria. The general phrase “an aluminum die-cast part” is not enough to assess feasibility, timing, and cost.

If the process has not been fixed, request a technical and feasibility review . The data status, part size, functional need, or demand plan may require comparison of several routes. Project information can be submitted through Start a Project .

A Simple Pattern for Writing a Technical Specification

A clear subject line might read: “Production review for [name/application] housing, using [grade or material requirement], delivered [as-cast or finished].” State the proposed process, drawing revision, volume, and critical features separately. If aluminum HPDC on a cold-chamber machine is intended, say so explicitly.

Also state the die status: does it exist, require review, or need to be designed and built? Explain what a reference sample demonstrates and which features still require an engineering decision. This information makes the order scope clearer to both parties.

State the Process Precisely in Your RFQ

  • State the part name and application; do not write only “an aluminum part.”
  • If the route is fixed, state the material and process type alongside die casting.
  • Provide the 3D model, drawing, or available sample and the validity status of each.
  • List critical characteristics, sealing, appearance, coating, and finishing operations separately.
  • Share the approximate production volume and product-change plan with the engineering team.
  • If you are unsure of the process, request a feasibility review without predetermining the outcome.

Frequently Asked Questions

Which is correct: die cast, diecast, or die casting?

“Die casting” is the standard process term; “die cast” and “diecast” are also common in different grammatical and general contexts. Consistent wording and a clear material and process description matter more than spelling alone.

Is every part made in a metal mold a die casting?

No. Gravity permanent-mold casting and other methods also use metal tooling. The filling mechanism and process type—such as HPDC or LPDC—must be defined.

Are all aluminum die-cast parts made on cold-chamber machines?

Cold-chamber processing is the common route for aluminum HPDC. The exact system and any assisted technology cannot be inferred from the alloy name alone; the grade, machine, and actual production route must be confirmed for the project.

References and Further Reading

  1. NADCA — Frequently Asked Questions ↗Definition of high-pressure die casting using a reusable steel die.
  2. The Aluminum Association — Processing 101 ↗Overview of aluminum die casting, permanent-mold casting, and sand casting.
  3. NADCA Design — Cold Chamber Process ↗Cold-chamber arrangement and transfer of molten metal to the injection system.
  4. NADCA Design — Hot Chamber Process ↗Hot-chamber applications and alloy compatibility with molten-metal contact components.
  5. Ou et al. (2020) — Advanced Process Simulation of Low Pressure Die Cast A356 Aluminum Automotive Wheels—Part I, Process Characterization ↗Industrial study of LPDC for an A356 aluminum wheel and its filling arrangement.2020 · DOI: 10.3390/met10050563
  6. Iwata et al. (2012) — Compression Behavior of Entrapped Gas in High Pressure Diecasting ↗Experiment on entrapped-gas behavior and the relationship between pressure and solidification in HPDC.2012 · DOI: 10.2320/matertrans.F-M2011858

From Understanding the Process to Reviewing an Order

If the manufacturing method is not yet selected, describe the application, part geometry, intended material, and demand plan in the initial request.

View the Related Capability → Send Project Information and Start a Review

Related Articles

Which Parts Are Suitable for Die Casting?What Information Should You Prepare for a Production RFQ?Selecting an Aluminum Alloy for Die-Cast Parts

Back to All Insights →